About oil issue - smoke

ock contains the cylinders. In engines with more than one cylinder they are usually arranged either in 1 row (straight engine) or 2 rows (boxer engine or V engine); 3 rows are occasionally used (W engine) in contemporary engines,

About oil issue - smoke best oil for Land Rover

Water-cooled engines contain passages

The base of a reciprocating internal combustion engine is the engine block, which is typically made of cast iron or aluminium. The engine block contains the cylinders. In engines with more than one cylinder they are usually arranged either in 1 row (straight engine) or 2 rows (boxer engine or V engine); 3 rows are occasionally used (W engine) in contemporary engines, and other engine configurations are possible and have been used. Single cylinder engines are common for motorcycles and in small engines of machinery. Water-cooled engines contain passages in the engine block where cooling fluid circulates (the water jacket). Some small engines are air-cooled, and instead of having a water jacket the cylinder block has fins protruding away from it to cool by directly transferring heat to the air. The cylinder walls are usually finished by honing to obtain a cross hatch, which is better able to retain the oil. A too rough surface would quickly harm the engine by excessive wear on the piston.

The pistons are short cylindrical parts which seal one end of the cylinder from the high pressure of the compressed air and combustion products and slide continuously within it while the engine is in operation. The top wall of the piston is termed its crown and is typically flat or concave. Some two-stroke engines use pistons with a deflector head. Pistons are open at the bottom and hollow except for an integral reinforcement structure (the piston web). When an engine is working the gas pressure in the combustion chamber exerts a force on the piston crown which is transferred through its web to a gudgeon pin. Each piston has rings fitted around its circumference that mostly prevent the gases from leaking into the crankcase or the oil into the combustion chamber. A ventilation system drives the small amount of gas that escape past the pistons during normal operation (the blow-by gases) out of the crankcase so that it does not accumulate contaminating the oil and creating corrosion. In two-stroke gasoline engines the crankcase is part of the air?fuel path and due to the continuous flow of it they do not need a separate crankcase ventilation system.

Źródło: https://en.wikipedia.org/wiki/Internal_combustion_engine


Why invest in a bus driving course?

Buses are one of the most important means of communication. Thanks to them we can quickly get to a certain place without thinking about parking and so on. To become a bus driver it is necessary to invest in a special driver's license. Although at this rate it differs significantly from the "normal" driving license, license for driving cars, if only because of the size of the vehicle, which we, however, provides a number of people interesting experiences. Driving license this category is much less common than the traditional license category B, so that we can greatly increase your chances for example in the labor market, when put in their application documents mention of such a document.


Otto cycle

Diesel cycle
Main article: Diesel cycle
P-v Diagram for the Ideal Diesel cycle. The cycle follows the numbers 1?4 in clockwise direction.

Most truck and automotive diesel engines use a cycle reminiscent of a four-stroke cycle, but with a compression heating ignition system, rather than needing a separate ignition system. This variation is called the diesel cycle. In the diesel cycle, diesel fuel is injected directly into the cylinder so that combustion occurs at constant pressure, as the piston moves.

Otto cycle: Otto cycle is the typical cycle for most of the cars internal combustion engines, that work using gasoline as a fuel. Otto cycle is exactly the same one that was described for the four-stroke engine. It consists of the same four major steps: Intake, compression, ignition and exhaust.

PV diagram for Otto cycle On the PV-diagram, 1?2: Intake: suction stroke 2?3: Isentropic Compression stroke 3?4: Heat addition stroke 4?5: Exhaust stroke (Isentropic expansion) 5?2: Heat rejection The distance between points 1?2 is the stroke of the engine. By dividing V2/V1, we get: r, where r is called the compression ratio of the engine.

Źródło: https://en.wikipedia.org/wiki/Internal_combustion_engine



© 2019 http://masakra.com.pl/